The following settings, available on the Sync Tab, are used for setting up MIDI timecode generation from the ACID timeline.

Item

Description

Generate MIDI Timecode settings

These settings are for setting up MIDI timecode generation from the ACID timeline.

Output device

This option specifies the MIDI device to which the MIDI timecode will be sent. The MTC slave should also be set to this device.

Frame rate

This option specifies the frame rate for generating MIDI timecode. The MTC slave must be set to the same frame rate.

Generate MIDI Clock settings

These settings are for setting up MIDI clock generation from the ACID timeline.

Output device

This option specifies the MIDI device to which the MIDI clock will be sent. The MIDI clock slave should also be set to this device.

Trigger from MIDI Timecode settings

These settings are for setting up MIDI timecode triggering from another application or external device.

Input device

This option specifies the MIDI device from which the MIDI timecode will be received. The MTC master should also be set to this device.

Frame rate

This option specifies the frame rate at which the MTC master will send timecode to the ACID application.

Advanced

Click to open the Advanced Sync properties dialog for the selected MIDI settings.

Default All

Click to restore the Sync tab to the default settings.

The MIDI Timecode Input dialog appears when you have clicked on the Advanced button on the Sync tab of the Preferences dialog. This dialog contains advanced options for MIDI Time Code input. It is only displayed if a device is selected for MTC input on the previous dialog.

Item

Description

Free-wheel for time code loss

When this option is selected, playback will continue for a specified period of time without chasing if timecode is lost for some reason. Enabling this option can compensate for infrequent losses in timecode. If losses in timecode are frequent, troubleshooting should be done to find the cause of the problem.

Free-wheel slack time

Use the up and down arrows or enter a value in the edit box to specify the amount of time that timecode can be lost before the Free-wheel playback time starts. A longer time is more tolerant of breaks in the incoming timecode.

Free-wheel playback time

Specifies the amount of time that playback will continue after the Free-wheel slack time has been exceeded.

Synchronization delay time

Use the up and down arrows or enter a value in the edit box to specify the amount of time it takes for to synchronize itself to incoming timecode.

On slower computers, this time should be set to approximately two seconds. On faster computers, it may be set lower.

Acid Pro  Sync PreferencesSetting this value too low can sometimes result in audible pitch shifting at the start of playback.

Offset adjust

If synchronization is consistently behind or ahead of your MTC generator, enter a value in the box to adjust a synchronization offset with quarter-frame accuracy.

  • If synchronization is behind, set this value to a negative number. A setting of – 4 usually does the trick.

  • If synchronization is ahead, set this value to a positive number. A setting of +4 usually does the trick, though it is rare that ACID software will sync ahead.

This tab contains advanced options for MTC (MIDI timecode) input. It is only displayed if a device is selected for MTC input on the Sync tab of the main Preferences dialog.

Item

Description

Full-frame message generation

This option specifies when to send full-frame timecode messages while Generate MIDI Timecode is enabled. Full-frame messages are used by some external synchronizable audio devices to seek to a proper location prior to actually starting synchronization. Tape-based recorders especially benefit from seeking to full-frame messages because of the time it takes to move the transport to the proper location. However, fu
ll-frame messages are ignored by some devices and may actually cause unexpected behavior in other devices.

Check your hardware documentation to find out if they support full-frame messages.

The MIDI Clock Output dialog appears when you have clicked on the Advanced button on the Sync tab of the Preferences dialog. This dialog contains advanced options for MIDI Clock output. It is only displayed if a device is selected for MIDI Clock output on the previous dialog.

Item

Description

Send Start instead of Continue when beginning playback

Select this check box if you want to send a Start command rather than a Continue command when Generate MIDI Clock is enabled.

When the check box is cleared, a Continue command is sent, as this type of command allows the chasing device to start from a specific time. However, some older sequencers that support MIDI clock chase do not support the Continue command and must start playback from the beginning every time.

Song Position Pointer generation

This option specifies when to send Song Position Pointer messages while Generate MIDI Clock is enabled. Song Position Pointer messages are used by MIDI applications and devices to seek to a proper location prior to actually starting synchronization.

Preferences – Sync Tab

Options Menu

From the Options menu, choose Preferences and select the Sync tab to specify the options for setting up synchronization of other applications and devices with ACID software.


What do you want to learn more about?

Acid Pro  Sync Preferences Sync Settings

Acid Pro  Sync Preferences MIDI Timecode Input – Advanced Settings

Acid Pro  Sync Preferences MIDI Timecode Output – Advanced Settings

Acid Pro  Sync Preferences MIDI Clock Output – Advanced Settings

 

Sync Preferences